● Single componet

● Good elasticity, constant margin bonding.Excellent adhesion strength (>28MPa)

● Instant adhesion, easy operation

● Suitable for many kinds of light-curing restoration material

Product Description
NANOFIL? dental bonding agent B-10 is a light-curing total-etch adhesive belongs to polymer-based luting material. It is used in combination with light-curing composite or compomer filling materials, cements, and core build-up materials.The adhesive can be polymerized using halogen, LED, curing lights. NANOFIL? B-10 is available in bottles for free dosing.

Specification
5mL/bottle

Classification
Type 2, Class 2, Group 1 according to ISO 4049:2019.

Composition
NANOFIL? dental bonding agent B-10 mainly contains: PMGDM, HEMA, light cure initiator, acetone.

Indications
● All classes of fillings with light-curing composite.
● Core build-ups made of light-curing composite
● Intraoral repair of existing composite.
● Cementation of veneers and adhesive cementation of total-curing and dual curing composites.

Contraindications
Do not use in case of known hypersensitivity to bonding agent.
Do not use for veneer bonding or bonding of self-curing and dual-curing composite.

Side Effect
This product or one of its components may in particular case causes hypersensitive reactions.
Precautionary Measures

For Patients
This product contains certain substances that may cause allergic reactions through skin contact. Avoid using this product for patients who are allergic to acrylates.
If there is prolonged contact with oral tissue, please rinse with plenty of water.
If an allergic reaction occurs, please seek medical care as needed.

For Operators
This product contains substances that may cause an allergic reaction by limbs and eye contact. To reduce the risk of allergic response, use of protective gloves, goggle, and a no-touch technique is recommended.
If skin contact occurs, wash skin with soap and water.
If hands contact occurs, wash hands immediately with soap and water and then re-glove.
If eyes contact and allergic reaction occurs, seek medical attention as soon as possible.

Instruction for Use

1. Clean:
Rubber dam is recommended to make isolation.
1.1 For all classes of cavity, enamel/dentin surface should be cleaned with pumice and water to gently remove surface stains. Dry the cavity with air free of oil or by blotting with cotton pellets.
1.2 For core build up whole surface should be clean and dry.

2. Etching:
Use etching agent gel for etching treatment according to the instruction manual. For example, use NANOFIL? Etchant Gel AT-37 to etch tooth enamel for 20-30 seconds and dentin for 15 seconds.
Caution: For hypersensitive to Etching agent, etching should be avoided.

3. Dosing from the bottle:
Unscrew the cap of the bottle. Dose the necessary amount of NANOFIL? B-10 to target surface and protect the liquid from light. Close the cap tightly after dosing. If necessary, disinfect the bottle in accordance with local hygiene regulations.
Caution: Any contact with blood, saliva, or sulcus fluid will cause contamination.

4. Smear the adhesive:
Apply the adhesive with the little brush or other hygiene smear tools on all surfaces of the cavity and rub it in for 30 sec. Subsequently blow a gentle stream of air over the liquid for approx. 5 sec until the film no longer moves, indicating complete evaporation of the solvent. Cure the adhesive with a commonly used curing light for 20 sec. Depending on the indication, continue to work with the desired composite or compomer material as indicated in the pertinent instructions for use.
Caution: Avoid contact of the adhesive with mucosal tissue.

Storage Condition
1. This product is designed to be used at room temperature (2-25) °C/ (36-77) °F.
2. Do not expose materials to intense light.
3. Do not store materials in proximity to eugenol containing products.
4. Disinfect the products using an intermediate level disinfection process.

Expiration Date and Batch Number
See note on bottle/packaging.

Warranty
2 years.